Item Tag: Rigid

Esta plataforma oferece uma grande variedade de jogos que funcionam perfeitamente em qualquer dispositivo. Descubra a melhor experiência de cassino online na Funbet.

FAST USA New 2023 Mallet Finger Splint Brace Injured Joint Support Staks Bandage

Mallet Baseball Finger Splint. Brand new Staks Splint. FAST USA Shipping ! Velcro tape is included (fastened to the splint). To determine Your Size: Measure the joint circumference of your Proximal InterPhalangeal joint (PIP) (this is the second finger joint from the tip of each finger) and choose the size from the table below: Size Finger circumference 0: 38 – 42 mm 1: 42 – 48 mm 2: 48 – 53 mm 3: 53 – 55 mm 4: 55 – 60 mm 5: 60 – 65 mm 6: 65 – 70 mm Use: For protecting injured finger and keeping it in right position for faster healing. Allows more ventilation to injured finger than a heavy dressing or bandage. Protects finger from further injury during healing. Directions: Cleanse finger and wound. Stop any bleeding by direct pressure on wound using a clean gauze pad and elevating hand until bleeding has stopped. Apply small amount of antibiotic cream to any areas of broken skin. If skin is broken, use a small non-stick sterile gauze pad on wound. Wrap the gauze around finger 1-2 times. To secure the dressing, wrap thin strips of adhesive tape around gauze 1-2 times. Place the finger in the center of splint and gently apply pressure around splint. Splint should be snug but not tight. Secure splint to finger at the base with enclosed thin strip of adhesive Velcro tape, as shown on the picture. Wrap around finger once firmly but not too tight.If finger becomes blue, cold, or numb, loosen tape slightly. If redness, numbness, swelling, or pain persists, consult your doctor at once.Please be advised about eBay Delivery Estimates Disclaimer.These estimates are not guaranteed delivery dates. If you need this product by a certain date, purchase expedited shipping or email us before purchase for a shipping quote on 2 or 3 day delivery which is guaranteed.

BORT 104760 StabiloPlus Bridging Back Brace, Stabilization Lumbar Spine Brace

BORT StabiloPlus Bridging Back BraceSKU# 104760 PRODUCT-BENEFIT- Lumbar brace for bridging and for relief of the lumbar spine- Classical brace-shaped stable plastic bridging frame, anatomically pre-molded, thermoplastically adjustable- Non-elastic stabilization strap, individually adjustable- Height: ventral 17 cm (6.7 inches), dorsal 32 cm (12.6 inches)COLOUR: blackTHE MED-BENEFIT- High degree of stabilisation, can be gradually adjusted during the course of therapy (mobility function)- Additional ventral abdominal reinforcing plate- Basic support with an anatomic cut for optimum fitting- Easy to put on using the hand straps provided IndicationsSevere lower back pain with muscular weakness and significant hernia protrusion/prolapsewithout absolute indication for surgerysevere lumbar radicular or pseudo-radicular syndrome (refractory to conservative treatment)grade 2 spondylolisthesis with recurring lower back painsevere lumbar deformity with facet syndrome/arthrosispost-surgery for herniated disks without resulting paralysis with removal of the herniadecompression of the spinal canalsingle levelwithout deformitysingle level herniated disk surgeryshort stenosis of the spinal canal without significant paralysisvertebral fractures resulting from minor traumasuperior end plate deformities in the lumbar spine Sizes with measuring point Intended purpose This medical device is a brace for relief due to lordosis reduction and functional Immobilisation of the lumbar spine. Indications Severe lumboischialgia with muscular failure and substantial disc protrusion/prolapse with no clear OP indication, severe radicular, pseudo-radicular lumbar syndrome (resistant to conservative therapy), grade II spondylolisthesis with recurrent lumboischialgia, severe lumbar deformity with facet syndrome/arthrosis, state after thoracic surgery with no remaining paresis in case of cleared out thorax, single-level, without deformity, single-level thoracic surgery, spinal canal stenosis with a short walking distance without noteworthy paresis, vertebral fractures of a limited extent, superior end plate deformities in the lumbar spine. Contraindications Unclear soft tissue swellings, impaired sensation and circulation in the specific body region, skin diseases in the specific part of the body, latex allergy.Fitting instructions When delivered, the BORT StabiloPlus bridging brace is pre-set for maximum stabilisation. The bridging frame is attached to the support via the cloth bag, the more rigid version of the splints can be found in the splint bags. A splint set which is more flexible is included in the packaging. The additional abdominal pressure plate is also attached to the support. If required, it can be removed. It serves to increase abdominal counterpressure. EN BORT StabiloPlus Bridging Brace 07 EN Open the support, loosen the side tension straps, place the support around the waist and attach both closing sides using Velcro evenly one above the other with a slight pull of the hand straps. Ensure that the support is placed centrally on the torso and that the lower support edge (antecubital fold on the thigh) ends in the inguinal region. This is the only means to achieve an optimum effect from the BORT StabiloPlus bridging brace. Tighten the two lower belt straps evenly first; as a next step tighten the upper belt straps, enabling a guaranteed comfortable fit of the brace. If overtightened, the support may become wrinkled. During the course of therapy, it may become necessary to reduce the stabilising effect of the BORT StabiloPlus bridging brace. This decision is taken by the treating physician. For this, remove the more rigid version of the splints from the externally attached splint bag by folding the restraints back and removing the splints through the slit in the splint bag. The shorter, more flexible splints can then be inserted. The bridging segment and the abdominal reinforcement plate can also be removed from the support, as required, by loosening the Velcro fastenings and be individually thermoplastically adapted by the orthopaedic technician. Removal To remove the brace, open the tension straps and the front fastening and take the brace off. Material composition Polyamide (PA), elastodiene/latex (LA), viscose (CV) The sewn in textile label provides the precise material composition. The product contains latex and can trigger allergic reactions. Cleaning information Delicate hand wash 30 °C Do not bleach Do not dry in a tumble dryer Do not iron Do not clean chemically Do not use fabric conditioner. Air Dry Only… Stretch back into shape and dry in the fresh air. Close the Velcro fastening to avoid damage to other laundry items